We serviced a
WHIRLPOOL MICROWAVE
Model WOC54EC0HS20
Near Bridgeport, NY 13030
Chuck G
Job Details:
11/28/2023
When attempting to uninstall unit to install door switch i discovered that the unit would have to be pulled all the way out. I could not use the oven cart due to an island being in the way. I explained to the customer that the unit will have to be uninstalled in order to repair. Customer will call when unit is uninstalled. ; O-emld tckt
We serviced a
WHIRLPOOL DISHWASHER
Model KDTE334GPS
Near Brockport, NY 14420
Dave L
Job Details:
11/28/2023
Replaced upper rack adjusters. Tests ok. Y ; used 2 WPW10546503 (ADJUSTER) from stock
We serviced a
WHIRLPOOL WASHER
Model XXXXX
Near Syracuse, NY 13219
Chuck G
Job Details:
11/28/2023
"Mileage 48,772"
We serviced a
MAYTAG WASHER
Model MHW5630HC0
Near Rochester, NY 14612
Dave L
Job Details:
11/28/2023
Unit is consistently shutting down on off balance load errors. Ordering control and shocks. ; ordrng 1 W11322901 (Control) and 1 W11316766 (Shocks)
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300EWH01
Near Rochester, NY 14626
Dave L
Job Details:
11/27/2023
"Fresh food damper has become noisy and is not closing consistently. Ordering damper. ; ordrng 1 WPW10594329 (Damper), used 1 SH15 (Sh) from stock"
We serviced a
GE WASHER
Model GFW550SSN3WW
Near Irondequoit, NY 14609
James
Job Details:
11/27/2023
Drum sounds like its hitting inside of cabinet during spin cycle. Adjusted feet and pedestal and noise went away. Customer is to monitor.
We serviced a
GE DRYER
Model GHDP490EF5WW
Near Pittsford, NY 14534
Andres V
Job Details:
11/27/2023
I replaced the belt and the front bearing off unit. I put unit back together and tested it. Unit is working properly
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Rochester, NY 14626
Dave L
Job Details:
11/27/2023
Used wheels to repair and level when levelers that were overextended. Leveled unit until doors matched. Tests ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ02
Near Ontario, NY 14519
James
Job Details:
11/27/2023
"Freezer is frosting over and food freezing in ff section with control set to 1. Freezer seal pulled away from cabinet. Raised door, molded gasket and removed frost. Set temp to 4. Customer is to monitor."
We serviced a
GE REFRIGERATOR
Model GDE21EYKFS
Near Rochester, NY 14626
Dave L
Job Details:
11/27/2023
Moisture building in freezer due to right hand side of freezer door not shutting. Adjusted door until it closed properly.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS555SIHZ06
Near Rochester, NY 14616
Dave L
Job Details:
11/27/2023
Replaced freezer side door switch that was preventing use of dispenser and light. Tests ok. ; used 1 W11384469 (Switch) from stock
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Greece, NY 14616
Dave L
Job Details:
11/27/2023
Found cam pulley bolt loose Causing the belt to slip during spin. Tightened pulley . Tests ok
We serviced a
MAYTAG WASHER
Model MVWB855DC4
Near Rochester, NY 14612
Dave L
Job Details:
11/27/2023
Replaced latch and lid due to unit not starting. Tests ok.
We serviced a
WHIRLPOOL DRYER
Model WED5010LW1
Near Fairport, NY 14450
Andres V
Job Details:
11/27/2023
Unit turned on and heated properly but was making a rattling noise. I took unit apart and Inspected it but did not see anything loose causing sound. I put unit back together and tested it. Unit no longer makes noise.
We serviced a
WHIRLPOOL WASHER
Model WFW5605MW0
Near Ontario, NY 14519
James
Job Details:
11/27/2023
Removed door and inspected. New part damaged out of box. Re ordering part. ; ordrng 1 W11328751 (Door inspect)
We serviced a
WHIRLPOOL REFRIGERATOR
Model ED2FHEXVB01
Near Ontario, NY 14519
James
Job Details:
11/27/2023
Replaced switch holder and tested. Customer concerned that icemaker leaking into ice bin. Customer is to monitor if problem persists order WPW10190965
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS04
Near Victor, NY 14564
Andres V
Job Details:
11/27/2023
"I replaced the control board, mullium and ice maker. I filled ice maker using test 45 in diag. Ice maker filled, informed customer ice can take up to 24hrs to produce."
We serviced a
WHIRLPOOL DISHWASHER
Model WDF540PADW3
Near Irondequoit, NY 14617
Dave L
Job Details:
11/27/2023
"Unit is not cleaning well due to an open heating element . Ordering element ; ordrng 1 W10518394 (Heater), used 1 SH15 (Sh) from stock"
We serviced a
MAYTAG DRYER
Model MGD4500MW1
Near Rochester, NY 14621
Dave L
Job Details:
11/27/2023
Replaced knob and timer. New knob had scratch on its face. Re ordering knob. ; ordrng 1 W11675852 (Knob)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRR56X18FW03
Near Walworth, NY 14568
James
Job Details:
11/27/2023
Unit not defrosting. Ran heater in diagnostics. Replaced thermistor and defrosted evap. Customer is to monitor. If problem persists replace W11496883; used 1 W10316760 (Thermistor) from stock
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Victor, NY 14564
Andres V
Job Details:
11/27/2023
Unit was making a lot of noise caused by the drain hose hitting the back panel. I repositioned the hose so no longer makes contact.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEHZ00
Near Rochester, NY 14621
Dave L
Job Details:
11/27/2023
Cleared plugged defrost drain. ; dspstn on spec-tagged invntry: 1 819043 HEAT- PROBE
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDW09
Near Palmyra, NY 14522
James
Job Details:
11/27/2023
Door seals pulled out from door liners. Installed silicone behind gaskets and reinstalled. Doors sealed properly.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF707ESS01
Near Fairport, NY 14450
James
Job Details:
11/27/2023
Replaced leds and tested. Customer concerns with temperature. Temps were 38 and 3 set at 37 and 0. Checked frost pattern. Unit functions properly.
We serviced a
MAYTAG WASHER
Model MVWB850YWO
Near East Syracuse, NY 13057
Chuck G
Job Details:
11/27/2023
"Customer stated that they are finding water on the floor that is coming from unit. After inspecting the unit i found a water trail coming from the front left side of the unit indicating that its coming from the tub ring, suspension tested bad. I quoted customer for the repair but they declined due to the age of the unit."
We serviced a
WHIRLPOOL MICROWAVE
Model WMH76718AS0
Near Manlius, NY 13104
Chuck G
Job Details:
11/27/2023
Customer canceled service
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KWH2
Near Manlius, NY 13104
Chuck G
Job Details:
11/27/2023
"Customer is concerned about the discoloration on the inside lower left corner of tub. After inspecting unit i found that the inner tub is discolored at the water inlet. I explained to the customer that this is from something that is in the water supply, maybe iron. Unit tested good."
We serviced a
GE WASHER
Model GFW550SSNWW
Near Syracuse, NY 13207
Chuck G
Job Details:
11/27/2023
Upon arrival tub gasket clamp was not installed. After inspecting unit i found that the tub gasket clamp tested bad. Replaced clamp. Unit tested good
We serviced a
WHIRLPOOL WASHER
Model WTW6120HW1
Near Syracuse, NY 13219
Chuck G
Job Details:
11/27/2023
"Customer stated that unit is displaying a F6E1 error code and not starting a cycle. Error code F6E1-UI cant hear ACU. After inspecting unit i found that the control tested bad. Replaced control then after replacing control the new one blew, found that the drain pump tested bad, ohms 2.4. Unit needs control, drain pump and lower harness. Quoted customer for repair but they declined."
We serviced a
KITCHENAID DISHWASHER
Model KDPM604KPS2
Near Marcellus, NY 13108
Chuck G
Job Details:
11/27/2023
Replaced control. Ran a diagnostic cycle in which the unit operated as intended but there was suds when cycle completed so i explained to the customer about cycle selection and what dish soap will do once its Introduced into the unit. I started a pro wash cycle with a tablespoon of olive oil to get rid of the suds. Unit tested good
We serviced a
WHIRLPOOL RANGE
Model KSIB900ESS1
Near Victor, NY 14564
Andres V
Job Details:
11/27/2023
I was installing new harness when I noticed that it was missing part of it. Theirs no connections of the induction cooktop like the old one has. I called whirlpool parts and no one seems to know what I'm talking about. I will retry to order the part again incase someone missed part of it at the factory because schematics don't show it either ; ordrng 1 W10908894 (Harness)
We serviced a
KITCHENAID RANGE
Model KFGC558JSS01
Near Victor, NY 14564
Andres V
Job Details:
11/27/2023
I adjusted the burner so makes contact with electrode when sparking. Burner is now lighting properly.
We serviced a
MAYTAG WASHER
Model MVWC465HW2
Near Rochester, NY 14611
James
Job Details:
11/27/2023
Unit off balance. Found cam worn and making grinding noise. Need cam and actuator.
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Farmington, NY 14425
Andres V
Job Details:
11/27/2023
Rotor bolt was loose and causing unit to make grinding noise coming from slider. I also noticed unit was leaking gearcase oil. I reccomended customer gets gearcase replaced along with slider. Gave them a quote and they want to invest in a new washer.
We serviced a
WHIRLPOOL WASHER
Model WFW5605MW1
Near Canandaigua, NY 14424
Andres V
Job Details:
11/27/2023
Helped Zach with case swap.
We serviced a
KITCHENAID RANGE
Model KSDB900ESS4
Near Spencerport, NY 14559
Dave L
Job Details:
11/27/2023
Found burner adjustment was off preventing left front burner from lighting . Adjusted and cleaned burner. Tests ok.
We serviced a
KITCHENAID RANGE
Model KSEB900ESS6
Near Rochester, NY 14612
Dave L
Job Details:
11/27/2023
Cooling fan rattles and intermittently displays cooling fan speed error. Replaced cooling fan. Preheated to verify fan operation.
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Clay, NY 13090
Chuck G
Job Details:
11/27/2023
"Customer stated that the unit is not starting a cycle. Error code F3E2-pressure system fault. After inspecting the unit i discovered that the previous replaced control tested bad. Replaced control. Calibrated unit, ran a diagnostic cycle in which the unit operated as intended. I then started a cycle with a load of laundry in which the unit started with no issues. Unit tested good"
We serviced a
WHIRLPOOL MICROWAVE
Model WMH32519HZ07
Near Baldwinsville, NY 13027
Chuck G
Job Details:
11/27/2023
"Customer stated that the rack is arcing against the cabinet. After inspecting unit i found the arch markings on the rear right and left sides of cabinet, the left side appears to have a hole in it caused by an arch. Called safety and they will contact the customer. SR#7737767833"
We serviced a
WHIRLPOOL RANGE
Model WGE745C0FS01
Near Baldwinsville, NY 13027
Chuck G
Job Details:
11/27/2023
Customer stated that lower oven is not heating as it should. After inspecting unit i found that the issue is with the temp sensor. Unit needs lower oven temp sensor WP7430P044 and control W10877730; rqstng P&A on 1 WP7430P044 (Temp sensor) and 1 W10877730 (Control)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS322FDAW03
Near Hamlin, NY 14464
Dave L
Job Details:
11/21/2023
Replaced icemaker and ice bin.
We serviced a
WHIRLPOOL WASHER
Model WTW8200YW0
Near Hilton, NY 14468
Dave L
Job Details:
11/21/2023
"Bearing is worn and becoming loud. Ordering bearing. ; ordrng 1 W10435302 (Bearing), used 1 SH1 (Bearing) from stock"
We serviced a
KITCHENAID DISHWASHER
Model KDFE104KPS0
Near Hilton, NY 14468
Dave L
Job Details:
11/21/2023
Customer canceled at door
We serviced a
GE FREEZER
Model FUF14QRRBWW
Near Rochester, NY 14609
Andres V
Job Details:
11/21/2023
Unit has an internal leak where we cant fix. Used bubbles and took a video of where it's leaking. I called techline send them video and they deemed unit unrepairable. Sr 11570559
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW1
Near Rochester, NY 14612
Dave L
Job Details:
11/21/2023
Unit is making a grinding noise when washing heavier loads. Found that the unit is making uneven contact with the floor pan when in agitation causing the belt cover to get pushed up into motor pulley. Adjusted feet and installation. Customer to monitor. P
We serviced a
AMANA WASHER
Model NTW4519JW2
Near Rochester, NY 14624
Andres V
Job Details:
11/21/2023
Unit shaking is standard I informed customer that newer units will shake and make more noises then their old one will.
We serviced a
KITCHENAID OVEN
Model KSGG700EBS6
Near Webster, NY 14580
James
Job Details:
11/21/2023
Replaced control and ui. Tested successfully. Customer is to monitor.
We serviced a
MAYTAG RANGE
Model MER8800FZ0
Near Webster, NY 14580
James
Job Details:
11/21/2023
Replaced element and tested. 120 volt to element. 242 volts to unit. Need control. Customer opt to not repair.
We serviced a
KITCHENAID REFRIGERATOR
Model KRM706ESS01
Near Rochester, NY 14612
Dave L
Job Details:
11/21/2023
CustomerCanceled at the door.
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC703HPS04
Near North Chili, NY 14514
Andres V
Job Details:
11/21/2023
Installed new door. Tested out water and ice dispenser. also made sure it wasn't leaking. Used heat gun to help gasket mold and seal better. Unit is working properly.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT104TFDW00
Near Rochester, NY 14616
Dave L
Job Details:
11/21/2023
Opened sealed system to reveal contamination. Documented via pictures with tech line. Non repairable. SR7737843529
We serviced a
KITCHENAID OVEN
Model KEBK101SSS04
Near Irondequoit, NY 14617
Dave L
Job Details:
11/21/2023
"Bake element only receives 120vac. ; ordrng 1 WPW10119143 (Control), used 1 Sh2 (Sh) from stock"
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW2
Near Rochester, NY 14626
Dave L
Job Details:
11/21/2023
The control is no longer supplying voltage to the motor. Motor windings test out of range. Customer is going to replace
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW2
Near Murray, NY 14420
Dave L
Job Details:
11/21/2023
Suspension has failed causing unit to becomeOut of balance ordering suspension ; rqstng P&A on 1 W10780045 (Suspenstion)
We serviced a
GE REFRIGERATOR
Model GFE28GELIDS
Near Pittsford, NY 14534
James
Job Details:
11/21/2023
Replaced ff thermistor and control. Ff began cooling once plugged in.
We serviced a
WHIRLPOOL OVEN
Model WOES5030LZ01
Near Penfield, NY 14526
James
Job Details:
11/21/2023
Unit underbaking customer has to set temp 25 degrees over. Calibrated and tested. Oven was averaging 352 degrees at 350. Unit functions properly.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT710PAHZ1
Near Henrietta, NY 14467
Andres V
Job Details:
11/21/2023
"Informed customer that water in filter housing was normal and its so the pump doesn't run dry also top rack cup shelf fell out of place, put it back where it belongs."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDW09
Near Penfield, NY 14526
James
Job Details:
11/21/2023
Gaskets pulling loose. Temperature fluctuating in freezer. Installed adhesive behind door seals and reinstalled. Customer is to monitor temperature. If problem persists order W11666427; dspstn on spec-tagged invntry: 1 W10838574 GASKET
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ0
Near Irondequoit, NY 14609
James
Job Details:
11/21/2023
Unit randomly flashes f1e1 control error. Replaced ui and control. Unit functions properly.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Henrietta, NY 14467
Andres V
Job Details:
11/21/2023
I put unit into a diagnostic used test 4 to test damper. I had customer listen to noise and she said it sounded like it. Ordering new damper. ; ordrng 1 WPW10479155 (Damper)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDBM02
Near Pittsford, NY 14534
Andres V
Job Details:
11/21/2023
Unit is not dispensing ice. The auger motor is turning but the yoke is rounded and will not spin the ice maker tray. Unit needs new motor and yoke. Gave customer a quote but she wants to contact whirlpool first to see if they'll cover parts. WP63052-2 (impeller) WPW10317991 (motor)
We serviced a
KITCHENAID DISHWASHER
Model KDTE254ESS2
Near Cazenovia, NY 13035
Chuck G
Job Details:
11/21/2023
Replaced drain loop and drain hose. I ran a diagnostic cycle in which the unit operated as intended. Unit tested good
We serviced a
WHIRLPOOL DISHWASHER
Model WDT540HAMZ0
Near Cazenovia, NY 13035
Chuck G
Job Details:
11/21/2023
Customer stated that unit is rusting on the door at the vent. I verified issue. Ordering SS panel W11613485; ordrng 1 W11613485 (SS panel)
We serviced a
MAYTAG DRYER
Model MED7230HW3
Near Cazenovia, NY 13035
Chuck G
Job Details:
11/21/2023
"Customer stated that unit is not powering on. I verified the issue. After inspecting unit i found that the ribbon cable on the UI was not fully installed, i removed cable and installed ribbon cable. Control and power tested good. Unit tested good"
We serviced a
WHIRLPOOL RANGE
Model WFC310S0ES0
Near Cazenovia, NY 13035
Chuck G
Job Details:
11/21/2023
Customer stated that when cooking on a med temp the front left and rear right burners will burn a bright red like it was set to high. After inspecting unit i found that the issue is with the infinite switches. I explained to the customer what the issue is and quoted him for the repair but he declined.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDW09
Near Vernon, NY 13476
Chuck G
Job Details:
11/21/2023
"Customer stated that temps dont seem right, they are fluctuating up and down in both compartments. Compressor is drawing 1.2 amps, fresh food temp 36.7 and the freezer temp is .02. Evaporator has a full frost pattern, no ice/frost buildup. I advised customer to call whirlpool as all related parts have been changed. Unit tested good"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKW2
Near New Hartford, NY 13323
Chuck G
Job Details:
11/21/2023
"Customer stated that the top rack has come detached from rail. I verified issue. After inspecting unit i found that the rail guard holding the rack rollers in place had turned sideways causing the right side of the rack to come free, i reinstalled top rack. Rack, rails and rollers all tested good. No codes. I ran a diagnostic cycle in which the unit operated as intended. Unit tested good."
We serviced a
MAYTAG DISHWASHER
Model MDB9959SKZ0
Near Whitesboro, NY 13492
Chuck G
Job Details:
11/21/2023
"Customer stated that unit is blinking and not operating. Error code F8E4-float switch. I ran a diagnostic cycle in which i discovered that Suds is the issue flowing into the vent then into the drip tray. I reset the unit, i started a normal cycle with a tablespoon of olive oil in a coffee cup faced up, i asked customer to let the cycle complete and another cycle might have to be run. Unit tested good"
We serviced a
GE WASHER
Model GTW220ACK7WW
Near Utica, NY 13502
Chuck G
Job Details:
11/21/2023
"Customer stated that unit will not always complete a cycle. Error codes F31-out of balance and F6-critical flood level. After inspecting unit i found that the gearcase is leaking oil. Ordering gearcase WH03X33729, belt WH01X27538, pulley WH03X32097, spring WH01X24434, cable ties WH01X10217 and clutch WH05X24185; ordrng 1 WH03X33729 (Gearcase) and 1 WH01X27538 (Belt) and 1 WH03X32097 (Pulley) and 1 WH01X24434 (Spring) and 1 WH05X24185 (Clutch) and 5 WH01X10217 (Cable ties)s"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAHZ0
Near Rochester, NY 14620
Andres V
Job Details:
11/21/2023
"Customer has error code F1E2 for control issues. Talked to techline and they suggested turning off power to unit for a few minutes and trying if that doesn't work replace control. Customer wants to try cycling power first see if that works, if they call back order W11305297 ( control)"
We serviced a
MAYTAG REFRIGERATOR
Model MFI2067AES
Near Rochester, NY 14618
Andres V
Job Details:
11/21/2023
I replaced the control board and programmed it. I tested the water and ice dispenser they both work. Customer is to monitor situation. ; dspstn on spec-tagged invntry: 1 W10890094 CNTRL- ELEC
We serviced a
GENERAL ELECTRIC DRYER
Model HTX24EASK
Near Utica, NY 13502
Chuck G
Job Details:
11/21/2023
Unit was not on-site. ; schdld next appmnt for 12/8 FRI !
We serviced a
KITCHENAID RANGE
Model KSDG950ESS6
Near Rochester, NY 14607
James
Job Details:
11/21/2023
Dropped off part.
We serviced a
GE WASHER
Model GTW220ACK7WW
Near Utica, NY 13502
Chuck G
Job Details:
11/21/2023
"Customer stated that unit will not always complete a cycle. Error codes F31-out of balance and F6-critical flood level. After inspecting unit i found that the gearcase is leaking oil. Ordering gearcase WH03X33729, belt WH01X27538, pulley WH03X32097, spring WH01X24434, cable ties WH01X10217 and clutch WH05X24185; ordrng 1 WH03X33729 (Gearcase) and 1 WH01X27538 (Belt) and 1 WH03X32097 (Pulley) and 1 WH01X24434 (Spring) and 1 WH05X24185 (Clutch) and 5 WH01X10217 (Cable ties)s"
We serviced a
WHIRLPOOL OVEN
Model WOD51ES4EB00
Near Rochester, NY 14607
James
Job Details:
11/21/2023
Replaced control and tested. Problem remains. Upper fuse blown. Reinstalled control and tested. Lower oven functions. Need upper fuse. Refund difference from control towards fuse replacement. ; ordrng 1 W11034459 (Fuse) and 1 Sh15
We serviced a
MAYTAG DRYER
Model MGD7230HW0
Near Rochester, NY 14613
James
Job Details:
11/21/2023
Replaced thermal fuse and leveled unit. Unit functions properly.
We serviced a
WHIRLPOOL RANGE
Model WFG505M0MW0
Near Rochester, NY 14619
Andres V
Job Details:
11/21/2023
Customer had issue with middle burner not lighting all the way and oven cooking hot. I took burner apart and cleaned it out and also calibrated unit. Unit is working properly.
We serviced a
GE RANGE
Model RB787WH2WW
Near Rochester, NY 14607
Andres V
Job Details:
11/20/2023
Unit is 240v to bake element but element has no continuaty. Unit needs new element; ordrng 1 WB44K10005 (Bake element)
We serviced a
GE DISHWASHER
Model GDT605PMM0ES
Near Rochester, NY 14626
Dave L
Job Details:
11/20/2023
Replaced control UI and heater. Tested ok. Made customer aware of small momentary leak on supply line. Leak stopped once it was in use. Customer is going to have it replaced. Tested ok; used 1 SH1 (Sh) from stock
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near West Henrietta, NY 14586
Andres V
Job Details:
11/20/2023
Terminal block shorted out at the positive connector. Used a new terminal block from inventory. Put new connectors on and used customers old dryer power cord to connector power. Unit is working properly ; used 1 279320 (Block terminal) from stock
We serviced a
MAYTAG WASHER
Model MVWB865GC
Near Irondequoit, NY 14617
Dave L
Job Details:
11/20/2023
Lid isCracked ordering lid; ordrng 1 W11256781 (Lid)
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW
Near Pittsford, NY 14534
Andres V
Job Details:
11/20/2023
Customer canceled appt because she has not had water leaking in awhile.
We serviced a
GE DISHWASHER
Model GDT550PYR6FS
Near Pittsford, NY 14534
Andres V
Job Details:
11/20/2023
Water valve solenoid was stuck slightly open causing water to fill tub. I replaced the valve and tested it. Unit is working properly.
We serviced a
MAYTAG REFRIGERATOR
Model MRT311FFFZ02
Near Irondequoit, NY 14617
Dave L
Job Details:
11/20/2023
Replaced lh deli track that was preventing use of deli pan. Tests ok.
We serviced a
GE RANGE
Model JS645SL3SS
Near Victor, NY 14564
Andres V
Job Details:
11/20/2023
Front left burner temp sensor not working properly causing hot burner light to stay on. Unit needs new burner. ; ordrng 1 WB30X24111 (Burner)
We serviced a
MAYTAG REFRIGERATOR
Model MFF2055FRZ00
Near Macedon, NY 14502
Andres V
Job Details:
11/20/2023
I replaced the drain tube with new style p trap tube and followed instructions that came along with it. ; dspstn on spec-tagged invntry: 1 W11190084 TUBE-DRAIN
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Fairport, NY 14450
Andres V
Job Details:
11/20/2023
Installed new heating element assembly to prevent unit from frosting up.
We serviced a
WHIRLPOOL OVEN
Model KEBS277YBL2
Near Pittsford, NY 14534
Andres V
Job Details:
11/20/2023
I called customer and informed her that f1 error code is for having issues with control board but part is no longer available.
We serviced a
WHIRLPOOL RANGE
Model WFG505M0MS0
Near East Syracuse, NY 13057
Chuck G
Job Details:
11/20/2023
"Replaced right front electrode and spark module, electrode was sparking but to the side. New electrode tested bad. Reordering right front electrode W11666003, right front burner head W11435630 and right front cap ; ordrng 1 W11666003 (Right front electrode) and 1 W11435630 (Right front burner head) and 1 W11590055 (Right front cap)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRFF507HBS03
Near Manlius, NY 13104
Chuck G
Job Details:
11/20/2023
Customer canceled service at the door.
We serviced a
GE DISHWASHER
Model GSD3200J00CC
Near Rochester, NY 14607
Andres V
Job Details:
11/20/2023
"Installed new solenoid valve on unit. Tested it, unit now fills and washes properly."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Jamesville, NY 13078
Chuck G
Job Details:
11/20/2023
"Replaced basket. Calibrated unit. Ran a diagnostic cycle in which the unit operated as intended. I explained to the customer about cycle selection, how to load the unit and how much HE detergent to use. Unit tested good"
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS1
Near Syracuse, NY 13203
Chuck G
Job Details:
11/20/2023
Motor is receiving voltage. Replaced sump assembly. Unit tested good
We serviced a
WHIRLPOOL RANGE
Model WFG505M0BB2
Near Syracuse, NY 13207
Chuck G
Job Details:
11/20/2023
Customer didnt realize that unit was OOW. They canceled service as soon as i told them
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Rochester, NY 14621
Dave L
Job Details:
11/20/2023
Unit is not sensing water level. Pressure hose is clear. Transmission is noisy. Ordering control and Gearcase ; ordrng 1 W11513246 (Control) and 1 W11449840 (Gear case)
We serviced a
GENERAL ELECTRIC DISHWASHER
Model GDF640HSM5SS
Near Rochester, NY 14608
Dave L
Job Details:
11/20/2023
FTD error. Ordering pump. ; ordrng 1 WD19X25461 (Drain pump)
We serviced a
WHIRLPOOL DRYER
Model CEM2745FQ1
Near Rochester, NY 14620
Dave L
Job Details:
11/20/2023
Replaced timer due to open timer motor. Tests ok.
We serviced a
GE RANGE
Model JGBS66DEK6BB
Near Rochester, NY 14624
Dave L
Job Details:
11/20/2023
The control fails to power Ignitor. Ordering control and overlay. ; ordrng 1 WB27X44726 (Control) and 1 WB07X26702 (Overlay)
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS00
Near Brockport, NY 14420
Dave L
Job Details:
11/20/2023
Replace shorted freezer led module and secured loose door handle. Tests ok. ; used 1 W11601310 (MODULE) from stock
We serviced a
MAYTAG WASHER
Model MHW5630HC0
Near Hilton, NY 14468
Dave L
Job Details:
11/20/2023
Dispenser leaks during fill. Ordering dispenser; rqstng P&A on 1 W11524103 (Dispenser)