We serviced a
MAYTAG WASHER
Model MVW7230HW
Near Hilton, NY 14468
Dave L
Job Details:
02/21/2022
Unit would not spin due to a broken slider. Replaced slider and tested. Unit tested ok. ; dspstn on spec-tagged invntry: 1 W10734521 SLIDER
We serviced a
WHIRLPOOL DISHWASHER
Model KDTM404KPS0
Near Rochester, NY 14616
James
Job Details:
02/21/2022
Replaced control and ui. Unit powered on properly. Started cycle and found no issues.
We serviced a
WHIRLPOOL REFRIGERATOR
Model GB2FHDXWS02
Near Honeoye Falls, NY 14472
Steve
Job Details:
02/21/2022
S38253 replaced drain tube for plugged drain. Removed ice in drain and from freezer floor. ; dspstn on spec-tagged invntry: 1 W10619951 TUBE-DRAIN
We serviced a
WHIRLPOOL OVEN
Model RBS305PDQ17
Near Pittsford, NY 14534
Steve
Job Details:
02/21/2022
Found control over heating Temp sensor tested good. Quoted for repair; rqstng P&A on 1 WP8302994 (Control) and 1 Sh15 (Shipping)
We serviced a
MAYTAG DRYER
Model MEDB200VQ1
Near Webster, NY 14580
James
Job Details:
02/21/2022
Replaced heating element and reversed door catches. Unit functions properly one year warranty on repair.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRV986FDEM01
Near Webster, NY 14580
James
Job Details:
02/21/2022
Unit randomly trips breaker. Tested in Diagnostics and found no issues. Removed pantry harness completely and customer is to monitor. If problem persists replace control; ordrng 1 WPW10675033 (Control) and 1 Sh15
We serviced a
MAYTAG DISPOSER
Model DFC1500AAX-1
Near Webster, NY 14580
James
Job Details:
02/21/2022
Unit leaking and motor just hums. Unit needs to be replaced. Customer going to purchase disposal to be installed on next visit.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHB04
Near Webster, NY 14580
James
Job Details:
02/21/2022
Unit was installed and started leaking underneath. Customer found water line connection leaking and corrected issue. Took pictures of floor damage and informed customer to contact seller. Doors uneven and filter shoots out of housing once water is used. Filter wont click into housing. Ordering housing and level doors on return. ; ordrng 1 WPW10394053 (Housing)
We serviced a
WHIRLPOOL DRYER
Model WED49STBW1
Near Rochester, NY 14626
Dave L
Job Details:
02/21/2022
Customer stating that they have to run the dryer twice before clothes are dry. Verified airflow was good. Dryer cycling off at 160 degrees F on high. Customer had a load of laundry ready for me when I arrived placed items in the dryer and ran them on time dry for 30 minutes. Items were dry.
We serviced a
CROSLEY DRYER
Model VED6505GW0
Near Rochester, NY 14606
Steve
Job Details:
02/21/2022
Ordering door switch for not starting. ; ordrng 1 WPW10237959 (Door switch)
We serviced a
MAYTAG DRYER
Model MDG5500AWW
Near Rochester, NY 14620
Steve
Job Details:
02/21/2022
Ordering belt and coils for broken belt and clothes wet at end of cycle. ; ordrng 1 WP33002535 (Belt) and 1 Sh15 (Shipping) and 1 279834 (Coils)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDM06
Near Rochester, NY 14607
Steve
Job Details:
02/21/2022
Replaced freezer door for cosmetic damage on delivery.
We serviced a
WHIRLPOOL DRYER
Model WED560LHW2
Near Rochester, NY 14607
Steve
Job Details:
02/21/2022
Replaced dryer door for cosmetic damage on delivery.
We serviced a
WHIRLPOOL REFRIGERATOR
Model MRT311FFFZ00
Near Rochester, NY 14615
Dave L
Job Details:
02/21/2022
Adjusted doors to try to even gap between fresh food and freezer doors. Was able to increase gap size and even out door gaps.
We serviced a
JENN AIR OVEN-MW COMBO
Model JMW2430WS02
Near Spencerport, NY 14559
Dave L
Job Details:
02/21/2022
Unit was not heating on arrival. Replaced magnetron and inverter due to no heatUnit tested good after repair.
We serviced a
JENN AIR OVEN-MW COMBO
Model JES9900BAS
Near Rush, NY 14543
Dave F
Job Details:
02/21/2022
Front right burner light is staying on and the element does not work. Unit needs new switch . Ordering switch and the knobs ; ordrng 1 WPW10185286 (switch-inf) and 2 WP74011580 (knob flex)s and 1 WP74011550 (knob) and 1 WP74011579 (knob cust)
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS0
Near Penfield, NY 14526
James
Job Details:
02/21/2022
Installed new control and tested. Ui will not function with new control. Replaced control with original and unit gives wash motor error. Replaced wash motor and performed heater update and tested. Unit functions properly. ; used 1 W11537778 (Heater) from stock
We serviced a
MAYTAG WASHER
Model MVWB835DW4
Near Spencerport, NY 14559
Dave L
Job Details:
02/21/2022
Replaced control due to incorrect fill level. Ran aNormal cycle to verify normal operation. Unit tested good.; dspstn on spec-tagged invntry: 1 W11170706 CONTROL
We serviced a
AMANA REFRIGERATOR
Model ASI2175GRS04
Near Rochester, NY 14606
Dave L
Job Details:
02/21/2022
Fresh food door will not seal and upper right hand corner. Unable to adjust with hinge or feet. Ordering door. Liner repair is discolored and is separating again at top. Ordering kit ; ordrng 1 LW11156544 (Door fresh food) and 1 8201700 (Liner repair kit)
We serviced a
KITCHENAID RANGE
Model KFED500ESS03
Near Penfield, NY 14526
James
Job Details:
02/21/2022
New top has scractches and has glue stuck on cooktop. Attempted to clean glass and was unable to clean with razor blade. Lf element is either on high or off. Tested and unit has defective infinite switch. Need new top and switch. Left cooktop for disposal and will return with side panel. ; ordrng 1 W10780927 (Top inspect) and 1 WPW10296657 (Switch)
We serviced a
WHIRLPOOL RANGE
Model WFC315S0JS0
Near Rochester, NY 14607
Steve
Job Details:
02/21/2022
Replaced the drawer panel for dent on delivery.
We serviced a
AMANA REFRIGERATOR
Model ASI2575GRB01
Near Rochester, NY 14616
Dave L
Job Details:
02/21/2022
Customer is concerned with temperatures and low ice production. Found unit set to minimum temperature setting. Unit on off cycle. Power cycled unit and set to recommended setting. Unit cycled on. Full and complete frost pattern. Rescheduled customer to recheck at this setting. ; schdld next appmnt for 2/23 WED !
We serviced a
WHIRLPOOL FREEZER
Model WRT312CZJW00
Near Avon, NY 14414
Dave F
Job Details:
02/21/2022
Freezer is a little bit to warm ice cream is soft. Freezer was turned to max but still not cold enough . Restricted the air flow to the freshfood section to keep unit running longer . Turned to recommended temperatures. Unit has full frost pattern and tested good .
We serviced a
KITCHENAID RANGE
Model KSDG950ESS
Near Skaneateles, NY 13152
Chuck G
Job Details:
02/18/2022
Replaced assembly display. Unit tested good
We serviced a
WHIRLPOOL DRYER
Model WED7120HW
Near Canandaigua, NY 14424
Chuck G
Job Details:
02/18/2022
"No heat, incoming voltage good . Element failed continuity test. Ordering element ; ordrng 1 WP3387747 (Heating element)"
We serviced a
WHIRLPOOL WASHER
Model MHW6630HC0
Near Shortsville, NY 14548
Chuck G
Job Details:
02/18/2022
"Unit had an F9E1 error code - long drain. Unstacked dryer from washer and cleaned out debris from drain pump, pump not accessible for customer. Tested unit on quick wash and it operated normally, completed cycle. Unit tested good"
We serviced a
MAYTAG DRYER
Model MEDB835DW4
Near Geneva, NY 14456
Chuck G
Job Details:
02/18/2022
"Squealing noise when running, replaced idler pulley. Unit tested good ; used 1 W279640 (Pulley) from stock"
We serviced a
WHIRLPOOL RANGE
Model WFG770H0FZ1
Near Canandaigua, NY 14424
Chuck G
Job Details:
02/17/2022
Replaced cooktop and burner covers. Unit tested good
We serviced a
MAYTAG DRYER
Model MGDC215EW
Near Walworth, NY 14568
Chuck G
Job Details:
02/17/2022
"Long drying time. I tested unit and its heating fine. Problem was with airflow, explained to customer that the problem was in the vent going outside. Unit tested good"
We serviced a
MAYTAG DRYER
Model MED7230HW0
Near Macedon, NY 14502
Chuck G
Job Details:
02/17/2022
"Replaced control , i tested unit for 15 minutes and it preformed normally. Unit tested good"
We serviced a
WHIRLPOOL RANGE
Model WFG770H0FZ1
Near Canandaigua, NY 14424
Chuck G
Job Details:
02/17/2022
Replaced cooktop and burner covers. Unit tested good
We serviced a
WHIRLPOOL RANGE
Model WFE505W0JV0
Near Geneva, NY 14456
Chuck G
Job Details:
02/17/2022
"Replaced gasket , unit tested good"
We serviced a
MAYTAG WASHER
Model MVWC565FW2
Near Auburn, NY 13021
Chuck G
Job Details:
02/17/2022
"Customer stated that unit was not powering on. I inspected all connections and verified that the unit was getting the proper voltage. The unit was in lockout mode. I canceled the cycle and ran a diagnostic cycle in which i discovered the unit was not draining probably , i cleaned out the debris from the drain pump. I noticed that the unit had the Nydec actuator, replaced actuator. Ran another diagnostic test cycle and unit ran normally. Unit tested good ; used 1 W10913953 (Actuator) from stock"
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW0
Near Auburn, NY 13021
Chuck G
Job Details:
02/17/2022
"Customer stated that the unit seemed to Shake and stuck on sensor mode. Only one stored code, F0E5 - off balance. I ran a diagnostic test cycle and which it tested good. I level the unit , calibrated unit and i helped customer download, sign in to the Whirlpool app in order to update the unit. I confirmed the update was complete . Ran another diagnostic. Unit tested good"
We serviced a
KITCHENAID COOKTOP
Model KCGS556ESS02
Near Geneva, NY 14456
Chuck G
Job Details:
02/16/2022
"Customer stated that the flames are too high. I verified that the flames are too high, when initially turning on the burner the flame is going past the grates and melting the knobs and bezels. I did not have the tool to adjust flame so i must come back with the correct tool to adjust the flame lower. Customer stated that LP conversation was done by installer. Ordering 2 -knobs WPW105458492-bezels W10853046; ordrng 2 WPW10545849 (Knob ( Stainless ))s and 2 W10853046 (Bezel)s"
We serviced a
WHIRLPOOL WASHER
Model CAE2745FQ1
Near Geneva, NY 14456
Chuck G
Job Details:
02/16/2022
"Customer stated that as soon as the unit is plugged in it is starting a cycle on its own, i did confirm that the unit is starting cycle without coins when there is power to it. Confirmed that jumper wire is still installed. Ordering W11368855-main control W10285518 switch-cycW10491734 interfaceW11243585 -jumper Customer is working out payment with the office ; ordrng 1 W11368855 (Main control) and 1 W10285518 (Switch-cyc) and 1 W10491734 (Interface) and 1 W11243585 (Jumper), states that autho needed"
We serviced a
KITCHENAID DISHWASHER
Model KDTM404EBS
Near Palmyra, NY 14522
Chuck G
Job Details:
02/16/2022
"Customer stated that the top rack was broken. I inspected rack and discovered that the both adjusters had broken tabs and missing two strap tethers adjusters and one clip adjuster. Ordering adjuster, tether adjusters and clip adjuster. ; ordrng 2 WPW10195839 (Strap, tether adjuster)s and 1 WPW10250160 (Clip adjuster), used 2 WPW10546503 (Upper adjuster assembly) from stock"
We serviced a
WHIRLPOOL DRYER
Model WGD86HEBWO
Near Walworth, NY 14568
Chuck G
Job Details:
02/16/2022
"Customer stated that not all the lights where working on the console. I tested unit and found no defects, console was responding to commands and all relative lights to the cycle that was chosen was lit up. I explained to the customer what cycles where sensor cycles and what cycles where timed cycles. Unit tested good"
We serviced a
AMANA DRYER
Model NGD4655EW
Near Liverpool, NY 13090
Chuck G
Job Details:
02/16/2022
"Replaced blower wheel and motor. Tested unit, unit tested good"
We serviced a
KITCHENAID RANGE
Model KSDG950ESS
Near Skaneateles, NY 13152
Chuck G
Job Details:
02/15/2022
Installed new control and found that the display was still not working but the keypad would respond to commands. Ordering assembly display ; ordrng 1 W11105615 (Assembly display)
We serviced a
WHIRLPOOL DRYER
Model WGD4815EW3
Near Auburn, NY 13021
Chuck G
Job Details:
02/15/2022
"Customer stated that the unit was making a noise while in operation. I ran the unit and verified the noise. I inspected the rollers , idler and belt in which they checked out good. I then inspected blower housing and discovered that the noise was coming from the housing, i noticed that the foam was not attached fully. I reattach foam and reassembled. I then ran unit and the unit ran normally. Unit tested good"
We serviced a
WHIRLPOOL WASHER
Model WFW5620HW
Near Newark, NY 14513
Chuck G
Job Details:
02/15/2022
"Replaced dispenser, ran a test cycle in diagnostic mode and a quick wash cycle, unit operated normally with no leaks. Unit tested good ; dspstn on spec-tagged invntry: 1 W11524105 DRAWER"
We serviced a
WHIRLPOOL WASHER
Model MVWX655DW1
Near Fairport, NY 14450
Chuck G
Job Details:
02/15/2022
"Customer stated that unit would not agitate. I inspected actuator and found that the arm was moving freely. Replaced actuator , then calibrated unit and ran a diagnostic test cycle, unit ran normally. Unit tested good ; used 1 W10913953 (Actuator) from stock"
We serviced a
WHIRLPOOL RANGE
Model WFG515S0JS2
Near Seneca Falls, NY 13148
Chuck G
Job Details:
02/14/2022
"Replaced the range drawer front and inspected for sharp edges on new drawer, none were found . Unit tested good"
We serviced a
WHIRLPOOL WASHER
Model WFW5620HW2
Near Palmyra, NY 14522
Chuck G
Job Details:
02/14/2022
Customer stated that unit is leaking. I ran the unit in diagnostic mode and discovered that the customers drain line is leaking from behind the wall. I informed the customer that this is a plumbing issue. Unit tested good
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW
Near Shortsville, NY 14548
Chuck G
Job Details:
02/14/2022
Replaced wash plate and hub. Calibrated unit . Ran a diagnostic test cycle and a spin cycle in which unit ran normally. Unit tested good ; dspstn on spec-tagged invntry: 1 W10528947 HUB
We serviced a
WHIRLPOOL MICROWAVE
Model WMH78019HZ0
Near Geneva, NY 14456
Chuck G
Job Details:
02/14/2022
"Customer stated that the unit would not heat. I tested all door switches and they tested good. No error messages on display. I quoted customer for replacing magnetron, high voltage diode and capacitor. Customer is electing to purchase new unit."
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Auburn, NY 13021
Chuck G
Job Details:
02/14/2022
"Customer stated that the unit was not heating. I test the following for continuity - high limit thermostat, operating thermostat, thermal fuse, heating element and timer which they all passed. Inspected all harness connections, also good. Inspected all ducts for obstructions and also good. Unit tested good"
We serviced a
WHIRLPOOL OVEN
Model KEBC247KBL03
Near Skaneateles, NY 13152
Chuck G
Job Details:
02/14/2022
"Uninstalled the unit to get to the lower blower , removed blower, installed new blower, tested unit (passed) and then reinstalled unit. Performed another test. Unit tested good"
We serviced a
AMANA DRYER
Model NED4655EW1
Near Weedsport, NY 13166
Chuck G
Job Details:
02/11/2022
"Customer stated that the unit would not turn on. I checked the power going to the unit and its getting 240v. I then went to check the continuity on the thermal fuse and i noticed a loose connection meaning it was barely on there, thermal fuse tested good. i reconnected the connector then tested unit. Unit tested good"
We serviced a
MAYTAG DISHWASHER
Model MDB8989SHW
Near Canandaigua, NY 14424
Chuck G
Job Details:
02/11/2022
"Customer stated that the unit is not working. I confirmed that the water valve is working. I noticed that water is leaking from the sump gasket and the wash motor is not working. Ordering sump and motor assembly ; ordrng 1 WPW10591570 (Sump and motor), dspstn on spec-tagged invntry: 1 WPW10591570 SUMP & MOTOR"
We serviced a
AMANA MICROWAVE
Model AMV2307PFW07
Near Canandaigua, NY 14424
Chuck G
Job Details:
02/11/2022
Replaced turn-ring. Unit tested good
We serviced a
WHIRLPOOL DRYER
Model WED4815EW
Near Canandaigua, NY 14424
Chuck G
Job Details:
02/11/2022
"Customer stated that unit was taking a long time to dry. I inspected the unit and verified that the heating element was operating normally. I then inspected the blower wheel and it is operating normally. I performed a vent test with vent attached and the air quality was poor , then i performed another test without the vent attached and air quality tested good. I explained to the customer that there is am obstruction in her vent preventing good airflow. Unit tested good"
We serviced a
WHIRLPOOL RANGE
Model WFE505W0JV0
Near Geneva, NY 14456
Chuck G
Job Details:
02/11/2022
Customer stated that there was something wrong with the door gasket. I inspected gasket and noticed the gasket was missing the retaining clips. Ordering gasket ; ordrng 1 WPW10129032 (Gasket)
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS
Near Syracuse, NY 13224
Chuck G
Job Details:
02/11/2022
"Replaced control, water valve and track stop. Water valve is receiving the proper voltage. Unit tested good"
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKW0
Near Mendon, NY 14506
Dave F
Job Details:
02/11/2022
Dishwasher has brass fittings on heater . Ordering heater and following service pointer . ; ordrng 1 W11537778 (Heater)
We serviced a
MAYTAG FREEZER
Model MFT2976AEB00
Near Webster, NY 14580
James
Job Details:
02/11/2022
Unit too warm. Partial freezer frost pattern. 120psi at 1.3amps. Drain pan full of uv dye due to sealed system leak in ff section. Ordering ff evap and compressor; ordrng 2 W11506635 (Valve)s and 2 WPW10143759 (Uv drier)s and 4 Lok54s and 2 W11506619 (Lok 8)s and 2 W11504434 (Lok6)s and 2 W10895757 (Lok65)s and 1 W10917531 (Evap sealed system) and 1 W10276644 (Compressor) and 2 W11504420 (Lok86)s
We serviced a
KENMORE WASHER
Model 11082172810
Near Rochester, NY 14612
Dave L
Job Details:
02/11/2022
Customer requesting the v belt be changed due to spinning issue. Another company had righted belt a few weeks ago. Found a significant amount of oil actively dripping from the transmission. Belt was tight but the motor coils not move the transmission. Transmission is begging to fail and is NLA can not recommend a repair on this one.
We serviced a
WHIRLPOOL WASHER
Model GHW9150PW4
Near Rochester, NY 14626
Dave L
Job Details:
02/11/2022
Customer canceled at the door
We serviced a
WHIRLPOOL WASHER
Model MVWB750WQ1
Near Rochester, NY 14626
Dave L
Job Details:
02/11/2022
Customer stating unit would not complete cycles. E51 in diagnostics. Found severely worn tub bearing. Customer had unit half disassembled. Replaced bearing and removed a pile of socks from under the tub. Unit tested good. ; used 1 W10435302 (BEARING) from stock
We serviced a
MAYTAG WASHER
Model MVWB766FW1
Near Rochester, NY 14606
Dave L
Job Details:
02/11/2022
Replaced broken lid that was preventing the unit from locking. 5 year p&l warranty. ; dspstn on spec-tagged invntry: 1 W11259006 LID
We serviced a
WHIRLPOOL RANGE
Model WFC150M0JW1
Near Rochester, NY 14615
Dave L
Job Details:
02/11/2022
Replaced open oven sensor. Tested ok
We serviced a
WHIRLPOOL WASHER
Model WFW5620HWO
Near Webster, NY 14580
James
Job Details:
02/11/2022
Replaced bellows and cleaned filter. Tested quick wash cycle and found no leaks. One year warranty on repair. ; dspstn on spec-tagged invntry: 1 W11314648 BELLOW
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS00
Near Penfield, NY 14526
James
Job Details:
02/11/2022
"Freezer led module keeps shorting out. Replaced led and all leds began functioning. Customer is to monitor. If problem persists, replace led again along with control W11224256; dspstn on spec-tagged invntry: 1 W10695459 MODULE"
We serviced a
WHIRLPOOL REFRIGERATOR
Model MFI2568AEW
Near Penfield, NY 14526
James
Job Details:
02/11/2022
Replaced control and programmed. One year warranty on repair.
We serviced a
WHIRLPOOL COOKTOP
Model WFE770H0FZ1
Near Rochester, NY 14612
Dave L
Job Details:
02/11/2022
Replaced open bake element. Unit tested ok. ; used 1 Sh (Sh) from stock
We serviced a
WHIRLPOOL MICROWAVE
Model GH7208XRS1
Near Rochester, NY 14610
James
Job Details:
02/11/2022
Replaced ui and tested unit. Unit is functioning properly.
We serviced a
WHIRLPOOL FREEZER
Model WZF34X16DW00
Near Rochester, NY 14610
James
Job Details:
02/11/2022
Replaced control and thermistor. Ran forced defrost and defrosted evaporator. ; dspstn on spec-tagged invntry: 1 WPW10383615 THERMISTER-FREEZER
We serviced a
MAYTAG WASHER
Model MVWX655DW1
Near Rochester, NY 14612
Dave L
Job Details:
02/11/2022
The customer declined to have this unit diagnosed.
We serviced a
WHIRLPOOL DRYER
Model MGD7230HW
Near Rochester, NY 14612
Dave L
Job Details:
02/11/2022
"The blower wheel is stripped on the motor shaft causing a rumbling noise. Motor shaft will need to be cut to separate. Ordering blower and motor ; ordrng 1 279787 (Motor) and 1 WP697772 (Blower), dspstn on spec-tagged invntry: 1 4392067 REPAIR KIT"
We serviced a
MAYTAG WASHER
Model MVWC465HW2
Near Greece, NY 14626
James
Job Details:
02/11/2022
Replaced drain pump and tested. Calibrated unit and verified operation.
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ0
Near Rochester, NY 14612
James
Job Details:
02/11/2022
Replaced gasket and spray arms. Tested and found no leaks. Customer is to monitor.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT106TFDW01
Near Henrietta, NY 14467
Dave F
Job Details:
02/11/2022
"Customer is being reschedule unit was being moved to different location and need to order evaporator W10836706 and compressor WPW10507886 as it was missed during first parts orders; ordrng 1 W10836706 (evaporator) and 1 WPW10507886 (compressor), dspstn on spec-tagged invntry: 2 W11504416 COUPLER BR 8.5X6 2 W11504434 COUPLER BR 6X2 , 2 W11506619 COUPLER , 2 W11506620 COUPLER AL 8X8 , 2 W11506621 COUPLER BR 6 , 1 WPW10143759 DRIER-UV DYE , 2 W11504436 COUPLER AL BR 6X1.8 , 2 W11504445 COUPLER BR 5X4 , and 2 W11506623 COUPLER BR 10.5X8"
We serviced a
MAYTAG WASHER
Model MVWB835DW4
Near Hilton, NY 14468
Dave L
Job Details:
02/11/2022
Spoke to customer to pre order lid. Lid is covered from last repair. Customer to pay service fee and labor ; ordrng 1 W11259006 (Lid)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRQA59CNKZ
Near Rochester, NY 14612
James
Job Details:
02/11/2022
Replaced icemaker valve and cycled icemaker. Unit functions properly. ; dspstn on spec-tagged invntry: 1 W11455388 VALVE
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS0
Near Hilton, NY 14468
Dave L
Job Details:
02/11/2022
Replaced sump due to an open wash motor. Unit tested ok.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT104TFDT00
Near Rochester, NY 14625
Dave F
Job Details:
02/11/2022
Replaced control and harness. Heater now turns on . Defrosted unit .Unit tested good .
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW2
Near Fairport, NY 14450
Dave F
Job Details:
02/11/2022
Replaced suspension rods and control . Put towels in unit and got them wet . Ran unit on high spin . Unit tested good . If problem persists there is nothing else that can be ordered . Customer will need to speak with customer service.
We serviced a
KITCHENAID REFRIGERATOR
Model KFCS22EVMS2
Near Fairport, NY 14450
Dave F
Job Details:
02/11/2022
Replaced right hand door switch . Light is now working .
We serviced a
WHIRLPOOL RANGE
Model WFE525S0JZ0
Near Pittsford, NY 14534
Dave F
Job Details:
02/11/2022
replaced main harness for being burned and replaced power cord due to harness damaging the cord . Tested unit . Tested good .; dspstn on spec-tagged invntry: 1 PT220L CORD 4' 3W and 1 WPW10245259 BLOCK- TERM
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRB322DMBW02
Near Mendon, NY 14506
Dave F
Job Details:
02/11/2022
"Freshfood section is freezing items . Damper is working but is a little loud . Ordering damper , thermistor, control , went into settings in diagnostics and adjusted the temp manually a bit warmer to help with freezing right now . ; ordrng 1 12002355 (thermistor kit) and 1 WPW10594330 (control) and 1 WPW10503278 (refer elect cont brd)"
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS01
Near Honeoye Falls, NY 14472
Dave F
Job Details:
02/11/2022
"Replaced the pantry drawer control . Unit is running and making ice . If problem persists order W10804160 LED board , WPW10675033 main control and W11330971 UI"
We serviced a
GE RANGE
Model JGB635DEK4BB
Near Rochester, NY 14621
Evan
Job Details:
02/11/2022
Customer stated that ignitor clip was missing. Found that clip was missing and also front burner orifice holders are damaged. Ordering replacement holders and orifice ; ordrng 1 WB28X26604 (Orifice holder) and 1 WB28X26306 (Orifice holder) and 1 WB02X24727 (Orifice holder) and 1 WB02X24726 (Orifice Holder)
We serviced a
WHIRLPOOL WASHER
Model MVWC465HW3
Near Rochester, NY 14618
Evan
Job Details:
02/11/2022
Customer stated that unit would not spin. Found Nidec actuator on machine causing issue. Referring to service pointer W11531483 unit would not agitate. Replaced shifter and tested unit. Ran diagnostic cycle. Unit is draining and spinning as it should now. Autho: M11L7S1FPL1; dspstn on spec-tagged invntry: 1 WPW10006355 ACTUATOR
We serviced a
JENN AIR MICROWAVE
Model JMW2427DS00
Near Rochester, NY 14618
Evan
Job Details:
02/11/2022
Replacing console due to unit displaying f2e1 error for stuck key. Replaced console. Ran preheat to 350. Unit tested good
We serviced a
MAYTAG WASHER
Model MVW7230HW0
Near Webster, NY 14580
Evan
Job Details:
02/11/2022
Replacing control due to unit not progressing through cycle as it should. Replaced control. Ran multiple test cycles. Unit tested good. ; dspstn on spec-tagged invntry: 1 W11419171 CONTROL
We serviced a
KITCHENAID OVEN DOUBLE
Model KFGD500ESS04
Near Webster, NY 14580
Evan
Job Details:
02/11/2022
Replaced broiler pans due to pans being warped and making contact with racks. Replaced pans. Ran preheat to 350 in each oven. Unit tested good
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW0
Near Webster, NY 14580
Evan
Job Details:
02/11/2022
Customer stated that unit would not agitate. Removed rotor and discovered that slider had separated from plastic causing issue. Replaced slider and tested unit. Ran diagnostic cycle. Unit agitated and spun as it should. Unit tested good ; dspstn on spec-tagged invntry: 1 W10734521 SLIDER
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADW7
Near Webster, NY 14580
Evan
Job Details:
02/11/2022
"Customer stated that unit would not drain at the end of the wash cycle. Discovered error code f9e1 for long drain and also f4e3 for wash motor failure. Replaced drain pump. Unit now draining as it should. Unit tested good ; ordrng 1 W11025157 (Wash motor), dspstn on spec-tagged invntry: 1 W10876537 PUMP-DRAIN"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near Rochester, NY 14623
James
Job Details:
02/10/2022
Wheels broken off adjusters. Replaced both rack adjusters. Unit functions properly.
We serviced a
MAYTAG WASHER
Model MVWC565FW1
Near Rochester, NY 14623
Evan
Job Details:
02/10/2022
"Customer stated that unit would not spin out no matter load size. No error codes stored. Found gear case oil on belt guard. Agitator is also seized on shaft ordering gear case , agitator and drive hub. ; ordrng 1 W11161960 (Agitator) and 1 W11454734 (Gear case) and 1 W10528947 (Hub)"
We serviced a
MAYTAG REFRIGERATOR
Model MSS25N4MKZ04
Near Bloomfield, NY 14469
Dave F
Job Details:
02/10/2022
Door isnt staying closing and clicking. Adjusted the door hinge and set screws . Door is now staying closed .
We serviced a
CROSLEY WASHER
Model CRD1812TB
Near Rochester, NY 14621
Evan
Job Details:
02/10/2022
Customer stated that unit was delivered Saturday and did not work once plugged in. Removed back panel to inspect control. Once technician moved unit could see cockroaches climbing out from behind back panel. Advised customer to contact store
We serviced a
WHIRLPOOL WASHER
Model WFW5090JW 0
Near Rochester, NY 14610
Evan
Job Details:
02/10/2022
Customer stated that unit would not open door. Stated f24 code was flashing. Code relates to pressure system fault. Unit will not stop running drain pump even though pump is empty and pressure switch is clear. Called techline. SR: 7732940920 techline agent stated that control & switch will need to be replaced. Customer is contacting manufacturer. Below is a quote for repair if customer wants to proceedSwitch (W11044866) $22.00Control ( W11574592) $294.00S&H $15.00 Labor $90.95 Collected service call fee for now
We serviced a
KENMORE WASHER
Model 11026962500
Near Rochester, NY 14618
Evan
Job Details:
02/10/2022
Customer stated that unit was not level since repair. Found that front feet needed to be adjusted. Adjusted front feet. Tested unit in high spin. Unit tested good
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ00
Near Rochester, NY 14607
James
Job Details:
02/10/2022
Unit not dispensing ice. It appears ice clogsged dispenser and froz together into a clump. Defrosted dispenser and tested icemaker assembly. Unit functions properly. Customer going to order their own filter. ; dspstn on spec-tagged invntry: 1 W10873791 ICEMAKER ASSEMBLY
We serviced a
KITCHENAID REFRIGERATOR
Model KDFE104TWH
Near Pittsford, NY 14534
Steve
Job Details:
02/10/2022
Uninstalled and reinstalled due to dishwasher fell off shims and drain hose wrapped around sump and holding power supply wires. The dishwasher tests good.
We serviced a
WHIRLPOOL OVEN
Model KEBS208SSS04
Near Pittsford, NY 14534
Evan
Job Details:
02/10/2022
Customer stated that oven will not heat correctly. Found that bake element tested open causing issue. Ordering bake and broil element ; ordrng 1 WP9760774 (Broil element) and 1 WPW10207398 (Bake element)
We serviced a
WHIRLPOOL DISHWASHER
Model WDF330PAHB4
Near Canandaigua, NY 14424
Dave F
Job Details:
02/10/2022
Installed new wash pump and now the wash pump is pulsing checked voltage to unit 119 volts .. Checked voltage coming from control to pump and found its jumping around . Unit needs new control board W11087226 ; ordrng 1 W11087226 (control elec)
We serviced a
WHIRLPOOL COOKTOP
Model KICU509XBL00
Near Pittsford, NY 14534
Dave F
Job Details:
02/10/2022
Customer is having same issue .Called techline SR 7732934513 ordering module and all burners .; ordrng 1 W10857232 (module) and 2 WPW10396548 (hotplate)s and 1 W10396547 (hotplate) and 1 WPW10396549 (hotplate)